Netgear prosafe wg102 manual

Status: The status light on the WG should be blinking red. When the startup process is. Configure the wireless interface for wireless access. See the Reference. Test wireless connectivity using a computer with a wireless adapter. Now that you have finished the setup steps, you are ready to deploy the. WG in your network. If needed, you can now reconfigure the. Disconnect the WG and position it where you will deploy it. The best. Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage. Connect the power adapter to the wireless access point and plug the power. If you have a switch that. This can be especially convenient when the WG is. Using a computer with an Internet, or check for file and printer access on your network. In order to connect to. Note: If you cannot connect, see to Troubleshooting Tips in this guide or the.

Page Page 1 Page 2. Need help? Post your question in this forum. Content of pages Page 1 e. If it is not, make sure that the Ethernet cable is securely attached at both ends. Estimated Installation Time: 30 minutes. Prepare a computer with an Ethernet adapter. Configure the computer with a static IP address of Connect an Ethernet cable from the WG to the computer point A in the illustration.

Securely insert the other end of the cable into the WG Ethernet port point B in the illustration. The best location is elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless coverage area, and within line of sight of all the mobile devices.

Connect the power adapter to the wireless access point and plug the power adapter in to a power outlet. Power: The power light on the WG should be steady green. If the power light is not lit, check the connections, and check if the power outlet is controlled by a wall switch that is turned off. When the startup process is complete, the status light should be steady green to indicate that the WG is ready. You must connect a suitable antenna to the Wireless Access Point before powering on the access point.

See the Reference Manual for full instructions. Test wireless connectivity using a computer with a wireless adapter configured according to the wireless settings you just set in the WG to establish a wireless connection to the WG Now that you have finished the setup steps, you are ready to deploy the WG in your network. If you have a switch that provides PoE, you will not need to use the power adapter to power the WG This can be especially convenient when the WG is installed in a high location far away from a power outlet.

Now, Verify Wireless Connectivity Using a computer with an In order to connect to the Internet, your network must include a router that provides Internet access. Page 2 Troubleshooting Tips You cannot configure the wireless access point from a browser.

Here are some tips for correcting simple problems you may have. Make sure the connected device is turned on. The WLAN light does not blink during wireless activity. If the WLAN activity light remains off while the WG is transmitting or receiving data, disconnect the adapter from its power source and then plug it in again.

The WG default IP address is The WG default setting is for a static IP address. If the network where you are connecting it is using DHCP, configure it accordingly. You cannot access the Internet or the LAN with a wireless-capable computer. Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence.

When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act. For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information. You will receive the manual in your email within minutes.

If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual. Would you like to receive an email when new answers and questions are posted? Please enter your email address. Netgear WG Manual. Get this manual by email Other manuals of this product.

December All rights reserved. Other brand and product names are trademarks or. Information is subject to change without notice. Here are some tips for correcting simple problems you may have. You cannot configure the wireless access point from a browser. The WG default IP address is. The WG You cannot access the Internet or the LAN with a. There is a configuration problem.